Skip to content
Guide

What Is a Cut List? Definition, Example and Free Template

A cut list, also called a cutting list, is a table of every part you need to cut for a project. Each row is one part, with its name, finished length, width and thickness, how many you need, and the material. Many cut lists also note grain direction and which edges get edge banding.

You write the cut list from the drawing, take it to the saw, and tick parts off as they come off the panel. It answers "what do I need to cut?", not "where on the sheet does each part go?". That second question is the cutting layout, which you can draw by hand or let an optimizer work out from the list. This guide covers what belongs in a cut list, how it differs from a cutting diagram and a bill of materials, a complete worked example for a bookcase, and a free cut list template you can fill in and import straight into an optimizer.

What Goes in a Cut List

There is no single standard form, but published examples agree on the core. Wood Designer describes a cut list as "simply a list of the parts in your project", giving for each part the quantity, the material and the "Dimensions – thickness, width and length", plus "Additional information like edging requirements and extra notes". Furniture maker Hank Gilpin, in Fine Woodworking, gives each part a letter, counts like parts in a quantity column, and keeps a notes column for reminders. Put together, a practical cut list has these columns:

ColumnWhat it holdsExample
IDA letter or number that ties the row to the drawingA
Part nameWhat the part isSide
QuantityHow many identical parts2
LengthFinished length, the dimension that runs with the grain1800 mm
WidthFinished width, across the grain300 mm
ThicknessBoard or sheet thickness18 mm
MaterialThe stock the part is cut fromBirch plywood
GrainWhether the grain must run along the length, across it, or does not matterAlong the length
Edge bandingWhich edges get banded, and with whatFront edge, 0.5 mm birch
NotesAnything the saw operator needs to knowDrill shelf-pin holes

Two conventions save most of the confusion. First, write finished sizes, the size the part has in the built piece. For solid wood, Gilpin adds a second column for rough length next to the exact length, because rough boards are cut long first and trimmed later. For sheet goods you normally cut straight to finished size. Second, keep length for the grain direction. If a part's grain must run along its 1800 mm side, that side is the length, even when it is not the longer side. Our guide to grain direction in panel cutting explains when this matters and when you can let parts rotate freely.

Cut List vs Cutting Diagram vs Bill of Materials

These three documents are often mixed up, and each answers a different question:

DocumentQuestion it answersWhat it contains
Cut listWhat parts do I need to cut?One row per part: size, quantity, material, grain, banding
Cutting diagram (layout, cut sheet)Where does each part sit on each sheet, and in what order do I cut?A drawing of every stock sheet with the parts placed on it, plus the offcuts
Bill of materials (BOM)What do I need to buy or pick to build the whole thing?Every item and its quantity, including parts, sub-assemblies and raw materials

A bill of materials is the wider list. Wikipedia defines it as a list of "the raw materials, sub-assemblies, intermediate assemblies, sub-components, parts", with the quantity of each needed to make the end product. For a cabinet, the BOM also includes hinges, screws, drawer runners and finish; the cut list is only the part of it that goes through the saw. The cutting diagram comes after the cut list: it takes the parts and arranges them on real sheets, with the saw kerf between them. A cut list never contains kerf, because kerf depends on how the parts are arranged, and the arrangement is not decided yet. The printable result of that step is often called a cut sheet; see PDF cut sheets explained for what a good one includes.

One more meaning you will meet if you search the term: in CAD software, "cut list" can also be a table generated from a 3D model. Onshape, for example, describes its Cut list feature as creating a composite part from frame segments "with a corresponding table listing each segment's properties". The idea is the same: a list of parts and their sizes, made from a model instead of by hand.

A Worked Example: Cut List for a Bookcase

Here is a complete cut list for a simple bookcase, 1800 mm tall and 800 mm wide. The carcass is 18 mm birch plywood and 300 mm deep. The two sides run the full height, the top and bottom fit between them, and three adjustable shelves sit on shelf pins. A 6 mm plywood back is nailed onto the back edges, so the finished bookcase stands 306 mm deep. The front edge of every 18 mm part gets 0.5 mm birch edge banding.

IDPartQtyLength (mm)Width (mm)Thickness (mm)MaterialGrainEdge banding
ASide2180030018Birch plywoodAlong lengthFront edge
BTop176430018Birch plywoodAlong lengthFront edge
CBottom176430018Birch plywoodAlong lengthFront edge
DShelf376229018Birch plywoodAlong lengthFront edge
EBack118008006Birch plywoodAlong lengthNone

Every number in the table comes from the overall size and one construction decision, which is what makes a cut list checkable:

  • Top and bottom, 764 mm: they fit between the sides, so 800 minus two 18 mm sides is 800 − 36 = 764 mm.
  • Shelves, 762 × 290 mm: 2 mm shorter than the gap so they drop in without binding, and 10 mm shallower than the carcass so they sit back from the front edge.
  • Back, 1800 × 800 mm: it covers the full back of the carcass, so it takes the outside height and width.
  • Part count: 2 + 1 + 1 + 3 = 7 parts in 18 mm plywood, plus 1 back in 6 mm, so 8 parts in total.
  • Edge banding: 2 × 1800 + 2 × 764 + 3 × 762 = 7,414 mm, about 7.4 m of banding before you allow a little extra for trimming the ends.
  • Area of the 18 mm parts: 1.080 + 0.458 + 0.663 = 2.20 m², against 2.98 m² for one 2440 × 1220 mm sheet (the common 1.2 by 2.4 metre size that Wikipedia lists as the most common plywood dimension). That is 74% of one sheet on paper.

Area on paper is not a layout, so we ran this exact list through CutPlan with its default 3.2 mm kerf and grain locked along the length. All seven 18 mm parts fit on one 2440 × 1220 mm sheet, and the back takes a second sheet of 6 mm plywood. The optimizer also cut the banded parts 0.5 mm narrower (299.5 mm and 289.5 mm), so they come out at the finished size once the banding is on. Our guide to how many sheets you need shows why area alone often under-orders on bigger projects, and the edge banding guide covers when banding thickness changes the cut size.

How to Write a Cut List by Hand or in a Spreadsheet

A cut list is quick to write if you work from a dimensioned drawing, one assembly at a time. Wood Designer puts it plainly: you write out "the details for each part cross referencing from a dimensioned drawing of your project", either on a printed template or "on a spreadsheet".

  1. Start from the drawing. Work from overall sizes and joinery, not from memory. Every size in the list should trace back to a dimension on the drawing and a decision like "the top fits between the sides".
  2. Go assembly by assembly. Carcass, then shelves, then back, then doors and drawers. It is much harder to forget a part when you finish one assembly before starting the next.
  3. Give each part an ID. A letter that also appears on the drawing, as Gilpin does, lets anyone match a part on the bench to its row.
  4. Write one row per part type with a quantity. Two identical sides are one row with quantity 2, not two rows.
  5. Group by material and thickness. Parts that come from the same stock belong together, because each group becomes its own set of sheets at the saw.
  6. Add grain and banding last. Mark grain only where it shows, so hidden parts stay free to rotate, and note exactly which edges are banded.
  7. Check it twice. Count the parts against the drawing, then add the sizes back up: the sides plus the parts between them should give the overall width.

In a spreadsheet, keep one unit for the whole sheet (all millimetres or all inches), put each value in its own column rather than writing "1800 x 300", and leave a tick column as Gilpin does for marking each part as cut. If you want a rough material estimate, add a column for length × width × quantity and total it per material, but treat that as a floor, not an order.

Free Cut List Template (CSV)

The template below is the bookcase cut list from this article, saved as a CSV file in the format CutPlan imports. Open it in Excel, Google Sheets, LibreOffice or any text editor, replace the example rows with your own parts, and save it as CSV again.

Download the Cut List Template

A CSV file with three sections: materials, stock sheets and parts. It opens in any spreadsheet and imports into CutPlan as it is.

Download cut-list-template.csv ↓

The file has three sections, each starting with a marker row. Keep the markers and the column order, and you can change everything else:

  • [MATERIALS]: one row per material with its name, type (sheet or banding), thickness and a display colour. Thickness lives here, so every part cut from "Birch plywood 18mm" is 18 mm thick.
  • [STOCK]: the sheets you have or will buy: length, width, quantity, material, a label and the sheet's grain.
  • [PARTS]: your cut list: length, width, quantity, material, a label (the ID and part name), grain, and four banding columns.

Two details are worth knowing before you edit it. Grain is written as vertical (along the length), horizontal (across it) or none. In the banding columns, Band_Left and Band_Right are the two edges that run along the part's length, and Band_Top and Band_Bottom are the two short ends; write the banding material's name in each edge that gets banded and leave the others empty. To use it, open the optimizer, choose Import CSV, pick the file and confirm the preview. Importing and calculating need no account. The app's own menu also has a CSV Template download with a short cabinet example in the same format.

Spreadsheet tip: when Excel or LibreOffice saves a CSV, it may pad the marker rows with extra commas. That is fine: the importer reads the first cell of each row, so the file still imports.

Common Cut List Mistakes

Watch for these when you check the list:

  • Inside and outside sizes mixed up, such as a top written at the full 800 mm when it actually fits between the sides.
  • No grain marked on visible parts, so a door or a side comes out with the grain running the wrong way.
  • Different thicknesses in one group, which hides the fact that a 6 mm back cannot come from an 18 mm sheet.
  • Banding left out of the list, so a thick edge band makes every banded part oversize.
  • No spare, so one mis-cut or a knot in the wrong place stops the job.

Each of these, with its fix and a worked example of where material disappears, is covered in 5 common cut list mistakes.

From Cut List to Cutting Layout

Once the list is right, the next job is the layout: arranging the parts on sheets so you buy as few as possible and every part keeps its grain. For a handful of parts you can do it on graph paper. For anything bigger, a cut list optimizer is faster, because it can try many arrangements and allow for the saw kerf between every part. The complete guide to cut list optimization explains how that works, and the step-by-step tutorial walks through a first project.

CutPlan.ai is the free online cut list optimizer we build, and it is what produced the bookcase layout above. It tries over 100 optimization strategies and draws every sheet with the parts labelled. The free plan is honest about its limits: calculating needs no account and you get 30 calculations a month, while exporting a PDF or CSV needs a free account and the free plan includes 5 exports a month, with a faint watermark on PDFs. DXF export for CNC is only in Pro, at $29 a month. If you only need one project finished cleanly, a Project Pack unlocks a project for good: 1 credit for $9, 3 for $22 or 5 for $32. If you are still choosing a tool, our comparison of the best cut list optimizer software covers the free and paid options side by side.

Turn Your Cut List into a Layout

Import the template or type your parts in, and CutPlan lays them out on your sheets in seconds. No account needed to calculate.

Open Optimizer →

Frequently Asked Questions

Is a cutting list the same as a cut list?

Yes, cutting list and cut list are two names for the same document: a table of every part to be cut, with its size, quantity and material. Some people also write it as one word, cutlist. Whatever you call it, it lists parts, not their positions on the sheet; that is the cutting diagram or layout.

Should a cut list use finished sizes or rough sizes?

A cut list should give finished sizes, the size each part has in the built piece. For sheet goods you usually cut straight to that size. For solid wood, some makers add a second column with a rough length, because boards are cut oversize first and trimmed to the exact length later.

Does a cut list include saw kerf?

No, a cut list does not include saw kerf. Kerf is the width of material the blade removes between two parts, so it depends on how the parts are arranged on the sheet, which is decided in the cutting layout. An optimizer adds the kerf you enter between every pair of neighbouring parts.

Is a cut list the same as a bill of materials?

No, a cut list is only the part of a bill of materials that goes through the saw. A bill of materials lists everything needed to build the finished piece, including hardware, fixings and finish, while a cut list lists the parts cut from boards and sheets, with their sizes.

Can I make a cut list in Excel or Google Sheets?

Yes, a spreadsheet is a good place for a cut list: one row per part, with separate columns for ID, name, quantity, length, width, thickness, material, grain and banding. The free template in this article is a CSV file that opens in Excel, Google Sheets or LibreOffice and imports into CutPlan without changes.

Guy Bader
Guy Bader
Founder & Maker at CutPlan

Guy founded CutPlan and builds its cut-list optimization engine. He works with woodworkers and cabinet shops to cut material waste, and writes about panel cutting, kerf, and getting clean cuts.

Add CutPlan as a preferred source on Google
Open Optimizer →